Texas Concrete Cost Guide — Per Sq Ft & Project Prices

🧮

Texas Concrete Cost Estimator

Instant installed-price estimate for any Texas project — priced for Texas labor & materials

Project type

Labor rates drive most of the difference.
Site prep is 20–30% of a Texas job.

Reinforcement

20 ft 20 ft 4 in thick 400 sq ft
$3,400
Estimate
$8.50
Per sq ft
5.2
Cubic yds
YOUR COST ESTIMATE
$3,400
Driveway · 400 sq ft · Houston
Concrete materials (5.2 yd³ @ $155/yd)$804
Labor & installation$2,596
Finish & upgrades$0
Region & soil adjustment$0
Project total$3,400

DIY route

$1,134
Materials + $250 tool rental + 10% contingency. Your labor is free — your weekend isn’t.

Pro installed

$3,400
Licensed crew, warranty, and a slab engineered for Texas clay.

Texas tip

For a 400 sq ft driveway in Houston, budget around $3,400 installed — then get 3 local quotes. Texas prices swing 20%+ between contractors.

📑 Table of Contents

[ Hide ]

    Concrete in Texas typically costs $6–$11 per square foot installed, putting the average 400 sq ft driveway at roughly $3,400 and a standard 1,200 sq ft home slab around $9,300. But that range hides a lot: a plain broom-finish patio in San Antonio can come in under $6 per square foot, while a stamped pool deck in Austin can push past $18. Texas has its own cost drivers — most famously the expansive clay soil that makes post-tensioned slabs the default foundation across much of the state — and understanding them is the difference between a fair quote and an expensive surprise.

    This guide gives you 2026 Texas concrete prices per square foot, per cubic yard, and per project, plus an instant Texas cost estimator and the soil, permit, and contractor knowledge you need before you sign anything.

    How Much Does Concrete Cost in Texas?

    For most residential projects, Texas concrete prices fall into predictable bands. The table below reflects installed prices — materials, labor, standard site prep, and contractor overhead — based on 2026 contractor data for the major Texas metros.

    Project typeLowAverageHigh
    Driveway$6 / sq ft$8.50 / sq ft$11 / sq ft
    Patio$6 / sq ft$8 / sq ft$10 / sq ft
    Concrete slab (4")$6.75 / sq ft$7.75 / sq ft$8.75 / sq ft
    Sidewalk$5 / sq ft$7 / sq ft$9 / sq ft
    Pool deck$8 / sq ft$11 / sq ft$14 / sq ft
    Home foundation$7 / sq ft$10 / sq ft$15 / sq ft

    The "low" end assumes a straightforward job: easy access, flat lot, plain broom finish, wire mesh reinforcement. The "high" end covers stamped or decorative finishes, difficult soil, demolition of old concrete, and premium metro labor (Austin runs roughly 10% above Houston). Decorative upgrades are the single biggest lever — stamped concrete alone typically adds $4–$7 per square foot over plain.

    Bar chart comparing installed concrete cost per square foot by project type in Texas

    Concrete Cost Per Cubic Yard in Texas

    If you're buying materials yourself — for a DIY pour or just to sanity-check a contractor's quote — ready-mix concrete in Texas runs about $140–$170 per cubic yard delivered for standard residential mixes, with $155 a fair planning number in the major metros.

    MixTypical usePrice / cubic yard
    3,000 PSIPatios, sidewalks, footings$140 – $160
    3,500–4,000 PSIDriveways, slabs$150 – $170
    Fiber-reinforcedCrack resistance, thin pours$160 – $180
    Short-load delivery feeOrders under ~4 yards$50 – $150 extra

    Two things catch Texans off guard here. First, the short-load fee: batch plants charge extra for small orders because the truck still rolls. If your project needs less than about 4 yards, ask for the short-load fee up front — it's often cheaper to round up your order than to pay it. Second, summer heat: many Texas plants add a retarder admixture ($5–$10 per yard) for hot-weather pours, which is money well spent when it's 100°F.

    Not sure how many yards your project needs? Our concrete bag calculator and concrete volume calculator do the math from your dimensions.

    Concrete Driveway Cost in Texas

    A concrete driveway is the most-searched concrete project in Texas, and the numbers are well documented: $6–$11 per square foot installed for a reinforced 4-inch driveway, per 2026 Texas contractor guides. Here's what that means for common sizes:

    Driveway sizePlain broom finishStamped / decorative
    1-car (10 × 20 ft)$1,200 – $2,200$2,000 – $3,600
    2-car (20 × 20 ft)$2,400 – $4,400$4,000 – $7,200
    3-car (30 × 20 ft)$3,600 – $6,600$6,000 – $10,800
    RV pad (14 × 40 ft, 6")$4,500 – $8,000$7,500 – $12,500

    Texas-specific driveway notes: go 5 inches thick if you park heavy trucks or an RV — the upgrade costs roughly $0.75–$1.50 more per square foot and prevents the cracking that plagues thin Texas driveways on clay. In Houston and East Texas, make sure the bid includes proper base compaction; contractors who skip it are the reason so many Gulf Coast driveways settle within five years. And if your quote seems high, remember site prep runs 20–30% of the job here — ask for it as a line item.

    Use the concrete driveway calculator for exact yardage, or the driveway cost estimator for a full price breakdown.

    Concrete Patio Cost in Texas

    A plain concrete patio in Texas costs $6–$10 per square foot installed, making a 12 × 12 ft patio roughly $900–$1,450. But Texas is stamped-concrete country — the long outdoor season means patios get used hard, and decorative finishes are the norm rather than the exception:

    Patio sizePlain / broomStampedExposed aggregate
    10 × 10 ft$600 – $1,000$1,000 – $1,800$900 – $1,500
    12 × 12 ft$900 – $1,450$1,450 – $2,600$1,300 – $2,200
    16 × 20 ft$1,900 – $3,200$3,200 – $5,800$2,900 – $4,800

    Stamped concrete in Texas runs $10–$18 per square foot — the pattern and color work costs real money, but it holds up well in the heat if it's sealed every 2–3 years. One Texas-specific tip: lighter stain colors and light-gray integral color keep a patio noticeably cooler underfoot in August. Dark stamped patterns look great in photos and feel like a griddle in person.

    Concrete Slab & Foundation Costs in Texas

    This is where Texas diverges from the rest of the country. Much of the state — Houston's Beaumont clay, the Dallas–Fort Worth metroplex, San Antonio, Austin — sits on expansive clay soil that swells when wet and shrinks when dry, moving inches between seasons. A conventional slab poured on that soil will crack. Texas builders answered with two foundation systems, and the cost difference between them matters:

    Cross-section diagram comparing a post-tension slab and a pier-and-beam foundation on expansive clay soil
    Post-tension slabPier-and-beam
    How it worksSteel cables tensioned after curing keep the slab in compressionConcrete piers drilled to stable soil carry beams + raised floor
    Best forMost Texas homes on clayVery unstable soil, flood zones, sloped lots
    Installed cost$7 – $12 / sq ft$10 – $16 / sq ft
    1,500 sq ft home$10,500 – $18,000$15,000 – $24,000
    Repair accessHarder — plumbing is in the slabEasy — crawl space access
    Repair riskCracks need specialistsAdjustable if piers settle

    Post-tension is the Texas default for new construction on clay — it's cheaper, faster, and engineered specifically for moving soil. Pier-and-beam costs 30–50% more but earns it back in repairability: foundation repair is practically its own industry in Texas, with 2026 repair bills ranging from $3,500 for minor pier adjustments to $42,000+ for major underpinning. If you're buying an older Texas home, budget for a foundation inspection ($300–$600) before you budget for the patio.

    Soil report: on new construction or additions over clay, a geotechnical soil report ($500–$1,500) tells the engineer exactly what the slab needs to resist. Skipping it to save $800 is how $20,000 foundation repairs start.

    What Drives Concrete Costs Up in Texas

    Five Texas-specific factors separate a $6/sq ft job from an $11/sq ft job:

    1. Site prep (20–30% of the total). The single biggest variable. Clearing, grading, compacting base material, and hauling off old concrete or caliche rock routinely accounts for a fifth to nearly a third of a Texas concrete bid. Always ask for site prep as a separate line item — lump-sum bids hide it.

    2. Expansive soil engineering. Post-tension cables, deeper beams, moisture barriers, and sometimes pier depth beyond 10 feet. In the worst Houston clay, foundation engineering alone can add $2–$4 per square foot.

    3. Summer heat. Pouring at 100°F+ requires retarder admixtures, early-morning pours, and sometimes ice in the mix — plus crews work slower. Summer bids run 5–10% higher than winter ones for the same job.

    4. Permits and HOAs. Most Texas cities require a permit for driveways and flatwork ($50–$300); Houston, Dallas, and Austin are stricter on drainage and right-of-way rules. HOAs add their own approval delays — and some mandate specific finishes.

    5. Access and demolition. Tearing out an old driveway ($1–$3 per sq ft for demo and haul-off), tight backyard access for a patio, or a sloped lot all push labor up. Rural jobs can actually cost less per square foot — but watch for travel surcharges and minimum-load fees from the batch plant.

    Concrete Prices by Texas City

    Labor is the main reason prices move between metros. Austin consistently prices highest; Houston is the baseline; rural Texas is cheapest but watch for delivery minimums.

    MetroDriveway (per sq ft)Notes
    Houston$6 – $10.50Baseline; worst expansive clay in the state
    Dallas–Fort Worth$6.50 – $11~5% above Houston; clay + growth demand
    Austin$7 – $12~10% premium; hottest contractor market
    San Antonio$6 – $10Slightly below Houston; limestone base helps
    El Paso$5.50 – $9.50Desert soils, less clay, lower labor
    Rural Texas$5 – $9Cheapest labor; confirm plant delivery range

    DIY vs Hiring a Concrete Contractor in Texas

    A small patio or sidewalk is a realistic Texas DIY project — materials for a 12 × 12 ft patio run about $350–$500, plus a $200–$300 mixer rental. But be honest about the Texas curveballs: finishing concrete in 95°F heat is a race against the set time, and anything structural (driveways carrying vehicles, foundations, anything over clay) belongs to a crew.

    The math from our estimator tells the story: a 400 sq ft driveway costs roughly $800 in materials but $3,400 installed. That $2,600 gap buys proper base prep, a crew that can screed before the heat wins, and — critically in Texas — a slab detailed for clay soil. DIY driveways on expansive clay are the most common source of "my driveway cracked in a year" stories.

    If you hire out: get three written quotes, check that the contractor carries general liability (Texas has no state license for concrete flatwork, so insurance + references are your filter), and make sure the bid specifies thickness, PSI, reinforcement type, and base prep. Never pay more than 30–50% up front.

    How to Save Money on Concrete in Texas

    Pour in fall or winter. Cooler weather means easier scheduling, sometimes 5–10% lower bids, and better curing conditions than August.

    Keep the design simple. Rectangles are cheap; curves, borders, and multiple elevations are where labor hours pile up. A plain rectangle with a broom finish is the best value per square foot in concrete.

    Bundle projects. Having the driveway, patio, and sidewalk poured in one mobilization saves the crew's setup cost — often 10–15% versus separate jobs.

    Handle demo yourself (carefully). Breaking out old concrete is labor-intensive but unskilled; renting a jackhammer for a weekend can save $1–$3 per square foot. Haul-off still costs — budget the dump fees.

    Choose wire mesh over rebar where appropriate. For patios and sidewalks, mesh is standard and sufficient; save the rebar upgrade (about $1/sq ft) for driveways and structural slabs.

    Ask about the short-load fee before you order. If you're DIYing under 4 yards, the fee can exceed the concrete cost. Round up or split a load with a neighbor.

    Texas Concrete Cost — Frequently Asked Questions

    1How much does a concrete driveway cost in Texas?
    A reinforced 4-inch concrete driveway in Texas costs $6–$11 per square foot installed. A standard 2-car driveway (20 × 20 ft) runs $2,400–$4,400 with a plain broom finish, or $4,000–$7,200 stamped. Site prep on Texas clay can add 20–30% on top of the base price.
    2What is the average cost per square foot for concrete in Texas?
    Across project types, expect $6–$11 per square foot installed for most residential concrete in Texas. Plain patios and sidewalks sit at the low end ($5–$8); driveways and slabs in the middle ($6.75–$11); stamped finishes and foundations at the high end ($10–$18).
    3How much does a cubic yard of concrete cost in Texas?
    Ready-mix concrete delivered in Texas costs roughly $140–$170 per cubic yard for standard 3,000–4,000 PSI residential mixes. Fiber-reinforced mixes run $160–$180. Orders under about 4 yards usually carry a $50–$150 short-load fee.
    4Is a post-tension slab better for Texas clay soil?
    Yes — post-tensioned slabs are the standard for Texas expansive clay. Steel cables tensioned after curing keep the slab in compression, so it moves as one unit when the soil swells and shrinks instead of cracking. It's also 30–50% cheaper than pier-and-beam for new construction.
    5How much more does pier-and-beam cost than a slab in Texas?
    Pier-and-beam foundations cost roughly $10–$16 per square foot versus $7–$12 for a post-tension slab — about 30–50% more. For a 1,500 sq ft home that's $15,000–$24,000 versus $10,500–$18,000. The premium buys easier plumbing access and adjustability if the soil moves.
    6Why is concrete cheaper in Texas than in California?
    Labor is the main reason — Texas concrete labor runs 30–40% below California's, and permitting is simpler and cheaper. A 4-inch slab that costs $6.75–$8.75 per square foot in Texas runs $9–$12 in California. Material costs (cement, aggregate) are similar; the gap is almost entirely labor, regulation, and seismic requirements.
    7Do I need a permit for a concrete driveway in Texas?
    Most Texas cities require a permit for driveway work, typically $50–$300. Houston, Dallas, and Austin also enforce drainage and right-of-way rules where the driveway meets the street. Check with your city's permitting office before work starts — and check HOA rules too, which are separate and often stricter about finishes.
    8How thick should a concrete driveway be in Texas?
    Four inches is standard for passenger vehicles; go five inches if you park heavy trucks, and six inches for RVs or commercial loads. On expansive clay, thickness matters less than reinforcement and base prep — a well-detailed 4-inch post-tension-style driveway outlasts a poorly based 6-inch one.
    9Can you pour concrete in Texas summer heat?
    Yes, but it needs hot-weather practices: early-morning pours, retarder admixtures ($5–$10 per yard), sunshades, and immediate curing compound or wet curing. Concrete sets dramatically faster above 95°F, which causes finishing problems and weak surfaces. If you can wait, fall pours cure better and often bid 5–10% cheaper.
    10How much does a 20×20 concrete patio cost in Texas?
    A 20 × 20 ft (400 sq ft) patio in Texas costs roughly $2,400–$4,000 plain, $4,000–$7,200 stamped, or $3,600–$6,000 exposed aggregate. DIY materials for the same patio run about $800–$1,100 including the short-load fee and mixer rental.
    11What does site prep add to concrete cost in Texas?
    Site prep — clearing, grading, compacting base, hauling spoil — typically adds 20–30% to a Texas concrete project. Demolishing old concrete adds another $1–$3 per square foot. Always get site prep as a separate line item; lump-sum bids hide the biggest variable in the job.
    12How long does a concrete driveway last in Texas?
    A properly built Texas driveway lasts 25–30 years: 4–5 inches thick, reinforced, on compacted base, with control joints every 8–12 feet and sealer every 3–5 years. Driveways that fail early almost always trace back to skipped base prep or no reinforcement on clay — not the concrete itself.
    13Should I get a soil report before pouring a foundation in Texas?
    For new construction or additions on clay — yes. A geotechnical report ($500–$1,500) tells the engineer the soil's plasticity and movement potential so the foundation can be designed for it. It's the cheapest insurance in Texas construction; skipping it is how $20,000 foundation repairs begin.
    14Does stamped concrete cost more in Texas?
    Yes — stamped concrete adds roughly $4–$7 per square foot over plain in Texas, putting most stamped patios and driveways at $10–$18 per square foot installed. The pattern work, coloring, and sealing are skilled labor. Budget for resealing every 2–3 years ($0.50–$1 per square foot) to protect the color from Texas sun.
    15How do I find a reliable concrete contractor in Texas?
    Get three written quotes and compare line items, not just totals. Texas has no state license for concrete flatwork, so verify general liability insurance and ask for local references — then drive past two of them. The bid should specify thickness, PSI, reinforcement, base prep, and finish. Never pay more than 30–50% up front, and be wary of any bid 30%+ below the others.